Here’s How You Can Detan Naturally Using Mango Pulp

Here's How You Can Detan Naturally Using Mango PulpNew

Summers are here in full swing and so is the need to binge on summer fruit like mango. Mango is not only delicious but also packs a host of health benefiting properties. It can do wonders for your overall health, provided it’s consumed in moderation. Other than its consumption, mango can be used on the face as well in the form of face packs. Mango pulp when applied onto the skin can treat a host of skin problems, one of which being tanned skin. With summer comes tanned skin. A lot of us look out for various beauty treatments to get rid of that summer tan. However, not many know that the same condition can be treated using natural stuff like mango. This humble summer fruit can be used to get rid of even the most stubborn tan. In order to get rid of that tanned skin, here are a few mango face packs that can come to great help. Read on to know how they can be applied.

1. Mango Pulp Face Pack

Having an uneven skin complexion could be a nightmare for many. In order to get rid of the same, mango pulp can prove to be quite beneficial. Mango has exfoliating properties that can help in keeping the skin well hydrated. Just extract mango pulp and rub it over your face for around 2-3 minutes. Allow it to stay for 5 minutes and rinse off with cold water. Doing so will help you bring back the glow back after a tan, further improving your skin complexion. Repeat the procedure thrice a week to see effective results.

mango pulp

Mango pulp can help you get rid of the summer tan

2. Mango And Besan Face Pack

This particular face pack can effectively keep tanned skin at bay. To make this face pack, you need to have pulp of ripe mango, two teaspoons of besan, 1/2 teaspoon of honey and few ground almonds. Take a bowl and add mango pulp in it. Then add Bengal gram flour (besan), almonds and honey into the pulp. Mix the ingredients properly to get a smooth paste-like consistency. Gently rub over the face and allow it to stay for around 10-12 minutes. Once it is done, rinse off with water. Use this face pack twice and watch out for results.

mango puree

This particular face pack can effectively keep tanned skin at bay

3. Mango And Curd Face Pack

If you happen to have an oily skin, then this face pack is just apt for you. Apart from the goodness of mangoes, this face pack has curd and honey as well. These ingredients are readily available in the kitchen and can help you fight with pigmentation and tanning in one go. Extract pulp from a ripe mango and add 1 tablespoon of curd and 1 teaspoons of honey in it. Mix the ingredients well. However, make sure that the face pack is of thick consistency. Apply this pack on your face and wash it off after 10 minutes.

curd face pack

This face pack will help you fight with pigmentation and tanning in one go

So, what are you waiting for? Make the most of this refreshing and healthy summer fruit by making the above mentioned face packs and say bye-bye to tanned skin.

[“source=food.ndtv”]

How to calibrate a monitor using Spyder5Pro and DisplayCAL

Spyder5Pro

The Spyder5 range of display calibrators are great little tools for fine-tuning monitors for a better visual experience, but the accompanying software from Datacolor isn’t the best option out there. Luckily, a fine community of developers continues to work on an open-source calibration suite called DisplayCAL (powered by ArgyllCMS), and it works with the Spyder5 range of calibrators. Here I run you through how to remove the Datacolor software and driver, install DisplayCAL and the necessary files and then get started.

  • Remove Datacolor software
  • Install DisplayCAL
  • Quick configuration

See at Amazon

How to remove Datacolor software

Spyder5

There’s no need to have the driver and software from Datacolor installed as we’ll be using open-source alternatives. If you haven’t installed the official Spyder5 software, you can skip this section. Should you already have it all set up, you will need to remove the suite and driver.

  1. Hit Windows + Q to bring up the search bar.
  2. Type in “add remove”.
  3. Select Add & Remove Programs.
  4. Scroll down and remove “Spyder5 software”.

Unfortunately, removing the software alone won’t get rid of everything. The driver for the calibrator will remain installed. To remove it as well, follow the following steps:

  1. Hit Windows + Q to bring up the search.
  2. Type in “device manager”.
  3. Select Device Manager.
  4. Search for the Spyder5 device listing. (It should be located under Universal Series Bus Controllers.)
  5. Right-click it and select uninstall device.

Install DisplayCAL

DisplayCAL

Now’s the time to prepare the system for calibration by installing DisplayCAL. You also need to fetch a driver for Spyder5 that works with DisplayCAL. (Don’t plug the Spyder5 in just yet!)

  1. Download and install DisplayCAL. (Choose the standalone package.)
  2. Run through the wizard and complete the installation.
  3. Launch DisplayCAL.
  4. Allow the suite to download and install the Argyll CMS color engine.
  5. Go to Tools > Instrument.DisplayCAL
  6. Choose “Install Argyll CMS instrument drivers”.
  7. Close down DisplayCAL and plug in the calibrator.

Fire up DisplayCAL, and you should now see the Spyder5 listed as an available instrument. Don’t start calibrating as you need to fetch the correction data from the official Spyder5 software.

Quick configuration

DisplayCAL

  1. Download the Spyder5Express software. (Don’t install it yet!)
  2. In DisplayCAL, go to Tools > Correction.DisplayCAL
  3. Choose “Import colorimeter corrections from other display profiling software.”
  4. Select Spyder5.
  5. Hit “Select File” and locate the Spyder5 installer.

This process should complete without a hitch. With all the steps done, you’re now ready to start the calibration process using Spyder5 and DisplayCAL.

[“Source-windowscentral”]